Can you try to change the geometry so that the different bridges are not consecutive in their corners ? It looks like the slicer is just trying to make one big bridge (in one direction) instead of 4 bridges in 4 directions.

Nice! I hope it’s not too hot when using it. I once made a case that wasn’t able to sustain the temperature.

They need a cloud connection for the setup, but there is a “LAN only mode” (there are still some messages yet). There is also a new X1E (enterprise edition) that is said to be totally offline if needed.

I love the musics. After finishing the game, I played the main theme in my car again and again and again.

Nice !

I would go with wood filament.

I just measured it and the overhang behind is half the bed and half the infamous cable. You need around 60cm between the front feet and the wall behind, for the cable not to be torn when the bed is all the way to the back.

The bed goes back and forth. On the back, you need the place since there is the infamous cable that should not be torn. On the front, the bed can go over the void. There is no need for a 70 cm large table, maybe 50cm with overhang.

It’s a mess. I have the A1 with AMS and it takes way more space than I wanted. The coreX with AMS are way more compact.

Edit.
Wide 80cm (with the poop chute on the left and the AMS on the right) Depth 70cm (with all the cables and the bed going back and forth) Height 60cm with the top roll

I would like to get one for our club but I can’t understand the wide variety of prices. $150 ? $500 ? $2000 ? $10000 ? $75000!! ? What’s the cheapest that is not a pain to use ?

What slicer is it ? I will check if it is possible to set no purge at all in BambuStudio - since I have an AMS lite.

It looks feasible with a purge multiplier set to 0. https://forum.bambulab.com/t/setting-an-unbeatable-record-no-flush-at-all/51052/4

I say to people : if you’re interested in 3D printing, you need two hobbies. 3D printing and anything else. The second hobby can be repairing things, a sport (spearfishing for me), board games, electronics, etc.

I started with a 100€ very small 3D printer for years (Tina2) and that was so worth it. Now I have a Bambulab with AMS and it’s night and day.

I agree with the other comments. Yet, it’s a beautiful design. What software do you use ?

But I like Nintendo consoles for their couch-multiplayer games. Like Wii-sport, Boom-blox, Just Dance, Mario party, Mario kart…

A Steam-deck is good for single players games.

LAN parties. I remember the first time I could connect two PC together. It was Doom, with a serial-to-serial cable. We were two players on the same fucking map. It was awesome!

Then coax cable networks with friends. We used to have two or three different networks during a LAN party since you could not disconnect the coax cable to add a player without stopping the current games. The players arrived later would plug a new network just for them, and launch a game waiting the first players to finish theirs.

Congratulations ! I usually make 4 or 5 iterations too for each piece, with my least favorite color (toilet paper pink that looked fuchsia on the website). I even launch a print and during the printing I correct my model based on the n-2 print.

There are some of these pumps in France. It infuriates me. The sound is horrible.

I have tried nearly everything. Chili powder or black pepper only works until the next dew.

I tried a special spray, it’s useless.

The only thing that worked for me to cover the whole garden was special grains made of wood and black pepper oil. You can throw it around the garden and it last one or two weeks.

For raised planter bed, I put nets originally used to cover trees for birds not to eat the fruits. It can be cut to any size and cats don’t like to walk on it. Some issues :

• it’s fragile. You need to replace it after one or two years.
• plants go through the net. It’s hard to remove then.
• once there was a tiny bird in it. I found it soon enough for it not to starve.

I do it in OpenSCAD too with a depth-map https://en.m.wikibooks.org/wiki/OpenSCAD_User_Manual/Other_Language_Features#surface

Thank you for your time! You’re so kind!

What matters :

• Auto calibration of Z-offset (multi-points). Your bed will warp with time and you don’t want to fight with it.
• PEI magnetic bed. You don’t want to fight with your things not sticking to the bed - or sticking too much. You may still have issues but less.

You will be happy with this as a cheap starter printer around 200$.

After some time, you may want to print bigger things, faster, and with ABS/ASA for technical parts. Then you could invest in a bigger printer, faster, hot and with an enclosure for ABS fumes and warping issues. The budget for this is 600-1000$.